Month: August 2023

Even more fencing on field #1

Steve HardinLeave a comment

Today went a lot better than yesterday. Mr Rainman and I installed the wife’s seat covers in her car. Wow, this is not an intuitive or easy job. It took us 75 minutes with both of us working on it and we never would have gotten it done if Mr Rainman had not taken the time to read the directions! I was gonna wing it! Nope, there are a lot of disconnect this one thing, leave off or detach and then put back after you have fished the straps past. Mr Rainman did bleed on some of the covers but I think I got all of the blood wiped up so wife won’t notice. The underside of the seats have some sharp areas. Since we could not get it in under 60 minutes the wife had to drive my lovely two door color car. Luckily, there were not going to be any passengers as the passenger door handle is still missing. I don’t think I will ever replace that handle, it’s superfluous.

I did order a new inside door handle for the pickup today. It’s just too hard to shut the door with no handle. The handle broke off at both screw attachment locations. I am hoping the $25 replacement will last another ten years. My left thumb is healing up nicely, the divot I took out with the electric shears has filled in and I just have an eraser sized scab left. I was sure I was going to have an upside down U forever on my thumb.

I have not been able to catch or kill a coyote yet. Today, we had the rifle with us the entire time and did not see a coyote. I have started to look into thermal imaging binoculars and scopes but they are expensive. Plus, it looks like the scopes all want to go on a picatinny rail and none of my hunting rifles have that. So I am still looking into it. This is a very dumb problem.

We need to get rid of some sheep. I took some pictures today and posted them for sale on Craigslist. We will see how that goes. I am going to email the auction site. I tried calling but their voicemail was full.

Both of my helpers came out to work on the fence in field #1. We got all of the wooden H brace cross pieces up and got one of the H braces fitted with high tension wire. We ran out of wire from our used stash but Mr Rainman had left with the Kubota tractor and it has the forks on it so we can just slip the full roll of wire onto a pallet fork and hold it in the air. This should make getting a piece off of the appropriate size easy. Instead we switched to installing T-posts with the tractor. The ground is fairly rock free and after two rains the ground is a lot softer than it was earlier in the summer. I only had to pound it about ten posts total with the tractor bucket. The rest I could just push in with the bucket (full of gravel and 150# of steel weights on the driver side of the push bucket. The Apprentice and I kept it up till about 1300. We also got the holes drilled for the gate so it can be installed next. I have learned that there are differing priorities for the Apprentice. When I asked the Apprentice why she was not wearing leather gloves when handling the T-posts and inserting them into the bucket driver I was informed that a weird suntan was appearing around her wrists. She did eventually put on some gloves as the sun heated the T-posts up enough they were too hot to handle. I refrained from commenting. We are still having grip exercise discussions every day she works. I keep telling her she needs to be able to handle tools for 8+ hours a day.

Fencing proceeds despite communication barriers

Steve Hardin1 Comment

Today the plan was to actually get some posts in the ground and get all of the needed materials to their appropriate locations. This proved much harder than one would assume as the day progressed. Both Mr Rainman and the Apprentice came out today to help with fencing. It took us a half an hour to gather tools and the rest of the railroad ties we needed. As the Apprentice and I got to the barn lot and were loading up large cedar posts to be the other half of an H brace with a railroad tie, I realized we needed more tools. I texted Mr Rainman and after the third text I realized that I just needed to walk over to the machine shed and help load more tools. We almost forgot the rifle, varmit getter. We loaded up 12- 16’x2”x8” rough cut boards onto the Kubota forks to use as the cross pieces for the H braces. That was almost too much weight to safely carry down the fields. The tractor back end kept bouncing off the ground when the path got too bumpy.

The plan was for Mr Rainman and I to start setting railroad ties after we drilled out the 12” holes. We had used the 6” auger yesterday to put in all of the holes and the plan was to widen the holes that needed railroad ties today. The field has dirt and not many rocks where we were digging but the ground has a lot of clay in it and can get very hard. Usually the big auger will just sit on top of the dirt and not cut down into it. It’s better since I welded the holder onto the arm and we stack tractor weights on it. We only had to use 100# of weights today.

The plan was to send the Apprentice back to the fence supply pile for a gate, there were three places on the farm she could find extra railroad ties, she needed to grab used T-posts from another spot and then grab the high tension wire that was on the ground near a culvert. I also have blocked off the wheat field access, I just covered it up with woven wire. This proved very problematic. You have to drive all the way down to field #3 to get out into the wheat field road before you can then drive up alongside the fields and get out onto the gravel road. We had to put one railroad tie on that fence alongside the road. She needed to deliver that said post. I thought I had explained the correct path. When she showed up in field #1 with the post and asked me how to get to the hole I had to reiterate all of the instructions, except this time she did not have to find the railroad tie, she had that. The tie got delivered to the correct spot and then she was supposed to get used T posts and the high tension wire.

Mr Rainman and I managed to get almost all of the railroad ties and cedar posts set when I asked him if he could see the Apprentice. Nope, it turns out that she drove past the used pile of T-posts six times and missed them every time. She had to drive down to the house and dig into the used post pile we have behind the grain bins.

Mr Rainman had to run to the house for a break so I asked him to grab a gate behind the grain bins. He comes rattling down the field with this super fancy very nice gate, not the gate from behind the grain bins. He states that I told him to go down to four corners and get that gate. You could not have picked a further spot from where we were fencing! He had to drive back and drop it off and get the gate we needed from behind the grain bins.

The only consistency here is me. I was the one giving instructions. There may have been some ambiguity present that I did not realize was present! The Apprentice and I got four sets of H braces built. She kept after it. As we were putting in the high tension tighteners she was having trouble using the fencing pliers, no grip strength. I gave her shit for not using the grip strengthener exercise I had told her about. She wants to be a farrier and will need to be able to hold onto the tools even when tired. She then voiced that she has been hurting all over her body since starting to work for me! Her hands hurt, her feet, her legs, her arms and her back all hurt all of the time! I laughed and told her mine do also but we still have to get stuff done. Say what you will, but the Apprentice just keeps coming back for more work. She digs in and just works at it until it is completed. You simply cannot ask for more and it is nice knowing she shows up to getter done. In a month, she goes off to school, so I will be keeping her as busy as possible until then.

Big surprise, we did not see a coyote that could be shot at. There was one across the street on the neighbors place but it was gone in about five seconds. I was up at 0115 due to the puppy barking, I went outside with a flashlight, suppressed 22 pistol and two extra clips to check on the ewe carcass we had left in the orchard, nothing there.

Barn Dig out completed

Steve HardinLeave a comment

Last week went fast and slow at the same time. The Apprentice stated that she wanted to work. The barn needs dug out and I have to go to the paying job. This seemed like a match made in heaven, to me. I attempted to teach The Apprentice how to drive the little tractor in and out of the barn. It is a tight fit and you have to watch the rear tires and the front bucket simultaneously so you don’t smash either one into the barn or knock out a roof support. After 20 minutes I realized that the time to just get in and out of the barn was going to be too long. So I had the Apprentice start shoveling the barn in areas the tractor would not go. I used the tractor to break up stuff it could reach and had the Apprentice make a long pile of poop in the center of the barn. She kept digging every day and I had to come home, eat dinner and then go out on the tractor and spend a couple of hours digging out the piles that were made in the center of the barn. She had that entire thing done in four days!

The barn floor is now drying out before we lay down some new bedding. I have to repair three boards that I managed to tear up with the tractor. This is only the second time I have torn up some boards when I was digging out the floor with the tractor. I just have to screw down three 4 foot long boards. It will take the impact driver to get the screws into the ancient wood I reused as the subfloor.

I had the Apprentice attempt to clean up the ground outside the barn with the tractor. The wind was blowing and after she ate about a half a pound of dust and poop she called it a day. I will have to come back later to scrape the ground clean. The Apprentice wanted to keep working but we were headed out of town on Friday so the apprentice agreed to come out early on Saturday and we would start in on the fence around field #1. I need to get that field fence up so the cows and sheep can get in there and eat it down. I have also been spending some time in the evenings picking blackberries. Annmarie uses them in her breakfast smoothies and we freeze them in individual serving portions. I have been picking wild blackberries and our domesticated thornless ones. The domesticated ones are huge in comparison to the wild, but the wild ones are much sweeter. The domesticated ones also have NO thorns, it is so pleasant to pick them. My hands look like I have been dragging them through rose bushes after picking wild berries for a couple of days. I was able to swing a deal with a friend for jam. I pick the blackberries and they make the jam! This way we both get some. They don’t like the hornets. I have not been stung a single time by hornets this year. I have managed to “pick” a couple off the blackberry bushes that I thought were fruit. It’s always a surprise when you go to put it in the bucket. I wash it, measure it and freeze it in known quantities so we can use it for jam and pies later in the year. I need to pick about four more gallons.

12 cups of wild blackberries

Fencing again

Steve HardinLeave a comment

The weekend was another one of those catch up ones. We ended up doing the things that had been put off but still needed to be done for various reasons. These weekends don’t feel as productive to me but they have to be done.

The Apprentice came out early Saturday and we prepped for fencing. This meant greasing the John Deere. This was a job I thought she might know how to do. The Apprentice assured me she had driven a large tractor before, a huge tractor. Yes, she had driven it but had not ever greased the fittings before. We ended up with grease on some things that were not fittings, but together we managed to get it done. We ended up laying out T posts and wooden stays all round field #1. We ran out of wooden stays! So I ended up splitting some of our own from the old cedar posts I had kept on the farm. I was able to get three stays from every post. I ended up breaking two shingle hammers doing it. I need to use the hand axe instead to get a weightier hit when splitting the post. I think I have enough posts left to split at least another 100 stays. After that I will have to buy some more. I always forget that the prep work for the fence is about half the install time. It takes a lot of time to measure and toss out all of the needed items. Doing this makes the fence go up a lot faster when the actual build begins. We even drove in some T posts by hand. This was not a job that the Apprentice does well. But she killed it when it came time to digging out the barn. Different muscles were used in each action. The post pounding muscles need a lot more work.

We spent most of Sunday out in the orchard. We had to pick the nectarines but they were not quite ripe. There was a huge storm coming into California and was supposed to bring potential flood levels of rain. The branches were already breaking on the nectarine tree so I figured it would be prudent to pick them now before the rain and storm ruined them. We tossed all of the tiny ones and any that had been eaten by earwigs over the fence for the cows and sheep to eat. We tossed out a lot of fruit and still ended up taking about 60# into the house and spreading it all over the dining room table to ripen over the next 1-2 weeks. I filled the entire table and was glad we fed the marginal stuff to the animals.

I even ended up going over to our Italian plum tree and tossing about 20# of fruit from the lower part of the tree over to the animals also. The branches were bending under the weight of all of the fruit. The pastures are getting pretty dry, we are a desert climate so I opened up the orchard for the cows and sheep after the Apprentice and I moved T posts and fencing wrap around all of the trees and raised it up back to it’s original high level. The cows still came in and reached up and ate all of the leaves, fruit and small branches they could reach. This has raised the branch level up significantly on all of the trees. There are still more Italian plums than we can safely eat left on the tree. This does not include the little yellow plums up in field #4 that should be ripe around the same time. The Asian pears are still not ripe yet and the fruit is very small this year. I will probably need to thin them harder next year to get a bigger pear.

The last half of Sunday was spent pounding posts into the ground. We even hooked up the post hole auger and switched out the 12” auger for the 6” auger. It was supposed to rain and I figured if I could get the 6” hole completed then the 12” auger should just follow the hole and tear it up. It just sits on the top of the dirt when it is super dry so following a hole should make it easy. We also put on the Texas T-post driving tool and filled the tractor bucket with gravel and 150# of steel tractor weights. We did manage to get some of the T-posts pounded in with the tractor. We also bent several of the posts in an attempt to use the tractor to pound them in. The heavier T posts make using the tractor doable.

Alpaca are sheared!

Steve HardinLeave a comment

I was able to finally catch up with a new helper, The Apprentice. They messaged me this morning and stated they could come out later in the day. This gave me enough time to work on some inside chores and do some laundry. I like to write blog entries on Sunday morning. I made breakfast shit on a shingle as there was extra time. It turned out very nice, I sent a picture to the child as she was not here for breakfast.

Once The Apprentice messaged me I headed out to get ready. The third manure spreader needed to be unloaded so I picked it off of the trailer with the tractor and put it next to the other two. We flipped gates and got everything ready to push the alpaca up toward the barn. We walked down and I fed apple slices to the three Musketeers and Snoop on the way to the barn and The Apprentice walked behind them encouraging them to follow. Once we got them into the barn lot we snagged one and let the games begin. They are so painful to shear. I had to use two blades for each alpaca. I really needed three blades. I think if we had done them earlier in the year there would not have been as much grit, dirt and rocks at the base of the hair. This would have made the blades last longer.

At one point on the last alpaca as I am trying to milk the second to last blade I stopped cutting any hair. Yet I still managed to slice out a divot of skin from my left thumb tip about 3/32” deep. It bled a lot. The Apprentice told me to just pore some of the powder dust for the alpaca toes onto my wound. It’s some kind of styptic powder designed to stop the bleed. I did it and it burns! The blood kept breaking through so I had to go find a first aid kit, a nonstick cotton pad and a roll of tape to get the bleeding stopped. I then forced my left hand into a leather glove to hold it all together. This worked very well for controlling the bleeding. I managed to barely get the last alpaca sheared. I had to use an old blade to get the final hair cut off.

We then went out to check on the red plums in the orchard, they were overripe and had fallen off the tree. I tossed them over the fence to the sheep. The Italian plums are just starting to turn colors so I give them 1-3 weeks still. The nectarines were all red and fairly big but still very hard. I think they need another 1-2 weeks. We tossed apples over the fence to the sheep and the Asian Pear has another 1-2 weeks. I will need to pay better attention to the orchard for the next 3 weeks. We swung by the garden and picked 3 pints of blackberries. Annmarie will now have fresh fruit for breakfast.

We then went out to the barn to discuss how to dig it out with the tractor. I had forgotten how hard it is to drive the little tractor in and out of the barn. After walking The Apprentice through the process I decided that they could dig out the edges of the barn and hand dig the momma baby area. The tractor can be used to move the debris once it is tossed outside the barn. They will be out in the morning to give it a whack. We will see.

When I came inside and took the bandage off of my injured finger it was black from the weird styptic powder. After a shower the edges of the wound are black. I think I chemically cauterized the wounds with the styptic powder. It never started bleeding again even after I held it under the shower for 10 minutes. Now I will have to wear a weird bandaid until it heals.