Abbriata M50 baler

Mechanic blood sacrifice

Steve HardinLeave a comment

Sunday I spent all day repairing equipment. The eight tines that I replaced on the power rake did not take too long. I was missing a bolt and had to dig through a three gallon bucket to find the correct size bolt and nut. I had cut late Saturday morning but the hay would not be ready to turn until Monday. It would have to wait until after I got off of work.

I do like the Abbriata M50 round baler but I snapped off two pickup tines on the same support bar and they created a stopping pin effect. The tines cannot be turned. I don’t have an overhead lift so I have to just lay on the ground and work on it. I also can crawl between the arms and reach inside the machine. It is not super comfortable and requires a lot of crawling around and stomach crunches to lift your upper body 6-8” off of the ground. I of course could not get three of the hay guides removed and my large 60V DeWalt grinder would not fit inside the opening and allow me to move it around enough to grind the heads off. I ended up driving to Pendleton and buying a 20V DeWalt grinder that is much smaller and fits inside the baler opening. I had all three bolt heads ground down in ten minutes. Of course once I got the guides out of the way I could hand turn the stubs of the bolts out of their retaining nuts. I was able to change out and install the new rake teeth and support bar.

There was a lot of swearing and I kept tearing up my hands and bleeding all over the equipment. I actually had to stop working and slide my hand into a leather glove so the blood would quit running down my knuckle. The leather glove absorbs blood and puts pressure on the wound. Eventually, I found a first aid kit on one of the tractors and used a bandage and some cleaning solution to treat the injury. There was more swearing before I was done. Once my abdominal muscles started to cramp up on me while I was reassembling the equipment I wanted to quit. But I knew I would just have to get it done eventually anyways so I might as well just get it done. My abdominal muscles still hurt two days later.

Monday I came home and spent four hours rowing hay. I had plans to row hay Sunday evening but the hay was still wet and instead I rolled bales that were on the ground in field #1. They were getting a wet spot on the bottom. I cannot pickup hay bales yet until I get them all cut. One the neighbors offered to have me come cut one of their grass fields so it doesn’t go to waste. I am still figuring out how to squeeze it in.

I did go out and work on making some bales today after work. I have about 1/3 of the hay put up but I was running out of shear bolts. The hay is in large rows and it keeps sucking in too much and snapping the shear bolt when I am close to full. I think I just need to dump lighter bales to avoid this issue. I will pick up more bolts tomorrow and hopefully finish tomorrow.

Getting lucky

Steve HardinLeave a comment

By the third dayI figured that a little bit of sunscreen on my face was not going to help if I spent all day on the tractor again. I had already managed to sunburn my lips. I took the, still in the box, sunshade that had been purchased for the older Kubota (Clementine) and installed it on the new one (Juicy). It took a couple of hours to get it all pieced together and up on the tractor. This one has a very nice locking mechanism that virtually makes it impossible for the shade to blow off the tractor. It is quite clever. After baling hay for an hour I asked myself why I did not do that two days earlier! Keeping that direct sun off of your face is a huge relief.

The hydraulic takeoffs do work! I only need one to get the dump lid on the baler to work and it worked great once I got the port all cleaned up. It had a lot of dust and dried grass in it. Unfortunately, I did order dust caps but do not order them by the size of the plug. They are ordered by the size of the hose. I did not know that until the wrong ones arrived in the mail. The correct size is now on order.

I spent all of Sunday baling hay until 2330. I really wanted to keep baling but we had scheduled help to come out on Monday at 0800 and help us with shear the alpaca. The haying got a lot easier once the sun went down. The moisture started to come out and the grass was not as slick. It baled super nice, no jams and it just wound up without any difficulties. I made twice as much progress after darkness hit. I started to just pick the big rows to bale as it was so fast. I figured I could get the smaller rows after we sheared the alpaca.

We had four alpaca that I had managed to get pinned on the back hillside. I thought they would cross the back creek. Nope, I ended up taking a header into the creek when the alpaca I was attempting to drag across the creek suddenly jumped and scrambled up the opposite side. Of course that same alpaca ended up jumping back across the creek to be with his buddies. One of the babies kicked Annmarie in the lower leg. It was a solid blow. That same alpaca proceeded to try and give us all the rear kick anytime we walked up behind it. So we grabbed it from the side when we drug it into the shearing area. It has grown significantly, it is probably our biggest alpaca now.

We did eventually get all four alpaca across the creek and I did not end up in it again. We only have six to shear, trim feet and inspect/cut teeth.

The shearing table makes it pretty easy to do everything. Our helper, the Quiet One, had never sheared alpaca before but she had just paid someone to come out to her place and shear her two alpaca. It was decided that she can just bring hers over to our place and we can just shear all of them on the same day. We had all six done within three hours. After three days of riding on the tractor my upper shoulders were killing me but I am getting much faster at shearing the alpaca than I used to when I started. I passed the trimmer off to the wife and Quiet One but ended up going back to it as I wanted to be done. I only cut three of them with the razor. No stitches have ever been necessary.

We dragged a tarp with the last two years worth of discarded hair over to the garden so we can use it as weed barrier. It makes great barrier. I showed the Quiet One how to work the new tractor and she will come out and mow the cheat grass down during the week. It needs it. I have been trying to mow the cheat grass while haying but once I started to bale nothing else gets done until hay is all formed into round bales. Once the bales are made I will leave them in the field for a couple of weeks. This is why I like the round bales so much better. They work for my delayed schedule.

I called in to the house and the wife brought me coffee out to the field! It was one of the best cups of coffee ever. I needed that coffee. Going around and around and watching the baler is monotonous. Even if I did manage to knock out two audio books over the weekend.

I went out and started to bale for another seven hours. I had enough material on the ground for approximately 12 more bales when the big boom was heard. The shear nut gave on the baler and I tried to replace it. I could not get the baler tines to move so I figured I better look closer to see what made that noise. One of the pickup tines exploded and broke some stuff that pinned the pickup shaft solid. I need three hours to tear into it and replace all the parts. It is close enough to finished to call it finished!

I now have to fix the sickle bar mower, the rake and the baler before I can cut some more hay. My plan is to fix the mower, cut hay, then fix the rake, rake and then fix the baler! As long as I get it fixed before I need it I am good to go.

Haying

Steve HardinLeave a comment

I have embraced the mechanic option out of necessity. All of my hay equipment is out of Italy and no one around here will work on it. So I have to fix it myself if I want to use it. I had to fix the sickle bar mower before I could go out and cut the first batch of hay on our place. Luckily, when I placed the order for parts I ordered everything I thought I would need except for one bolt that was going to have to come from Italy. That single bolt would have cost me $50. I figured I could find a bolt that would work for less than that.

I got the end of the sickle bar torn off and the new parts on. I was able to find a workable bolt to substitute for the Italy special. I went out and started to cut all of field #1. About halfway through it the mower stopped working. I had lost a bolt on the bar itself and one of the retainers had spun around. I drove back, replaced the bolt (I had purchased spares) and then tightened all of the bolts on the entire sickle bar and regreased everything. I went out and finished cutting the entire field. I did have to work past sundown. I did not want to come back and cut the last section in the morning. It would screw with the drying rate. When I got back I did notice that the Italy special replacement bolt had already bent. I am going to have to tear that fin off and beat on it with a very large hammer. I think I have gotten a sharper angle bent into it than it should have over the years of just normal usage. It needs some hammer therapy on the anvil to set it straight, literally! I know there is a second bolt available so I will replace the bent one when it is reassembled.

I found two batches of pheasant chicks out in the field when I was cutting, both were in the far middle of the pasture. I had to work hard not to run them over or cut them up with the bar. I managed to not hurt a single one.

I went out the next afternoon and turned and rowed the hay. So some of it had just barely had 24 hours or less since it was first cut. It was not super hot out but the hay was drying out fast. I rowed it with the power rake but again by the time I was done with the rake I had broken 8 tines! It was set too low and I had a lot of old tines on it. I do not believe there are very many old tines left. I had to go past dark again before it was completed. The hay was pretty dry so I knew I would be baling the next day. I will now need to repair this piece of equipment before it can be used again. I have instituted a repair personal priority system. The order in which the pieces of equipment are going to be needed are the order in which they are repaired. So the sickle bar mower first, then the powered rake then the baler.

We have our three yearling calves in the orchard near the houses and driveway. We are just tired of the butcher calves just being crazy because they never have to deal with humans until we run them into the pen to be killed. We are hoping that by us being able to talk to them and them being around us they will calm down. They are a little calmer currently than last year. The real problem is that Annmarie thinks we missed a testicle when we banded the calves. So far we have not ran them into the chute for a definitive grab/inspection. We are usually pretty careful about the cows when they are getting banded. Time will tell on this issue.

Fire everywhere

Steve Hardin1 Comment

Summer is grinding on with our entire region surrounded by wildfires. Luckily for us, the wheat field next to our houses was harvested last week. The wheat crop did very well, they harvested almost 48 bushels/acre. I realize that may seem low to a lot of people but for a dryland wheat crop in Eastern Oregon foothills with marginal soil that is fantastic. As an added bonus they disced a fire break around the entire stubble field so even if the field did catch fire it would be contained. The family leasing the property are great!

The smoke is bad. So bad I have started to snore nonstop due to congestion. We have two carbon air filters going in the house at all times in an attempt to cut it down. The fires are all around and have now moved into the surrounding mountains.

There is a small grass airstrip on our neighbor’s property parallel to the road. He uses it to fly his small plane. It has been taken over by fire fighting helicopters. There are 5-7 helicopters with assorted fuel tanks and support vehicles all over the runway. They fly mostly during the day and are dipping water from rivers, ponds and dams. This means they don’t have to bring any water out to the airstrip. There are all kinds of helicopters. I took the one picture from our front window.

The foot is improving but by the end of the week work my limp is back and I need some rest. We were sick on Friday but I did manage to go out and get started on fixing the Abbriata M50 round baler. The chain drive gears have worn down so badly that the chain no longer drives anything. It’s not hard to see why as some of the gears are worn down to nubs. I had looked at this a couple of months ago (before broken foot) and ordered all of the parts I thought I would need.

I am no mechanic. I don’t claim to be one but I am capable of doing it, I just don’t like it at all. That being said there is no one in the area that is used to working on a mini Italian round baler. Nor anyone that has better access to parts than just calling the same place I do. So I started to tear into the baler to get to the gears. By the time I had replaced three small gears I had almost everything off the one side. I am working on taking off two gears at the top that are chained together now so I can pull the gear off behind them. I really only need to pull one gear but I either break the chain or pull both gears off at the same time. It’s a toss up as to what is easier but by pulling off both front gears I can inspect and or replace both gears behind if needed. I know one gear needs replaced.

I need to get down below to the lower drive gears but after really looking at it I think I am going to have to jack up the one side of the baler, block it in place and remove the left wheel and all of the covers to gain access to those bottom gears. By the time I get everything fixed there won’t be anything on the drive side of the baler but exposed gears. This is why I hate doing mechanic work. I of course do not have all of the needed pieces to repair everything. I lost a key when I was pulling a gear off, so I need a replacement. I need to replace a small gear but it is not bolted in place it is welded to another piece so I did not order it before, will need to order. That special gear probably needs a bearing but I cannot tell yet as I have not removed it. I need a special shear pin I don’t have. Also, those double gears at the top I think are special and need another sprocket and gear setup I do not have.

I scrutinized the parts catalog and think I have the correct part t numbers now. On Monday I will call the dealer. The dealer and I will go over the diagrams together and I can walk them through what I am trying to replace. They are very good about helping me order the correct parts. I am replacing all of the bearings as I put in the new sprockets. The bearings feel good but I am not doing this again and you should never really reuse bearings. It just sets you up for failure.

Our siding is completed! It only took three and a half months. It looks amazing! There is a small piece of gutter to repair and we are going to get gutter installed over the back door. I don’t want an ice puddle forming directly outside the back door in the winter. This has allowed us to start watering the front yard finally. The entire yard was almost dead and the cheat grass is trying to take over. Water will help this dramatically. The dogs are coming in covered in dead grass all of the time.

Hopefully, we can start in on the gazebo this week. Mr Rainman will be out this week to help with that. There is one more field to finish mowing and all of the mowing will be done.