In a self defense move, I rolled all of the completed bales to the outside of the upper field. I was pretty certain I was going to have to pick them up alone and I wanted to make it easier on myself. I also wanted to leave the upper field clean so after I moved all the completed bales I went through the entire field again and raked it up a second time into four long rows. I managed to get another 20 bales out of the leftover grass from the first baling.
I left the bottom for an around a week, the Gingerman went over and raked it up into rows so I could sleep after working the night shift. It rained a 1/4” of rain later that week so I let it sit for a few more days before turning it again. I then let it sit for another five days in the hopes that it would dry out.
When I went over to bale it I had loaded up on shear bolts so the toolbar was all ready for me to repair any issues. I broke almost 25 shear bolts just baling the small bottom area. I would get close then an entire section of wet damp grass would jump into the baler and break the shear bolt! There was a very large amount of swearing involved in getting that field all baled up. By the time I was done it was taking me about three minutes to replace the shear bolt and get the tractor up and going again.
I had Mr Rainman for two days last weekend and we concentrated on getting the lower bales picked up one day. We were able to load up 30 bales into the back of the pickup, strap down each of the three rows and then creep up the steep rocky road in 4wd low. We only lost part of one load when the strap popped loose. We put 30 bales into each cow feeder at the house. So we filled all three feeders, one for the female pregnant cows, one for the feeder cows below and then one in Alcatraz. Currently, the only animals in Alcatraz are our three rams. Eventually, we will have to sort off the bull and put him in there with the rams.
We took the wettest bales and dumped them out for feed to be immediately eaten. Unfortunately, despite the farm looking like a food desert the cows and sheep are ignoring the lush green grass available in the feeders. Obviously, they know something we do not.
We came home earlier in the week and were greeted by the big truck sitting in the road. The Gingerman has been working on the truck, has it running and the brakes working on it. He has a few more things to do before we convert it to a fire fighting apparatus for the farm. We are going to put a couple of large totes for water, a pump and a hose reel on it so we can have some fire suppression if we decide to burn. On the off chance we have a fire nearby we can go out and meet it. It would have been handy when I caught the railroad ties on fire. Peeing on them to put out the fire takes a lot of effort.
The truck was blocked it just rolled down into the road, no one is sure how it did it. I could not get it started then the Gingerman told me that the battery was unhooked. I dropped the positive terminal on and smashed it a couple of times with a wrench. It still would not start. I took positive terminal wire off and then told Annmarie we would just need to drive around it for a week. The Gingerman stopped by a few days later and actually installed and tightened the battery post cable and it started up just fine! It is now blocked with some heavy duty tire chocks.
The back creek, Stewart Creek, is no longer running. There are a few spots of water behind our house but they will most likely be dry by the end of the week. The frogs will all move into our garden and tall grass. They can make quite the cacophony. We are so used to it that it is just drift off to sleep noise. The roosters crowing, the frogs serenading, the alpaca fighting , the sheep and lambs hollering, the cows bellowing and the occasional horse whinny it is mostly relaxing.
I picked the garlic today, we turned off the water about three weeks ago. I will let the dirt dry out and tomorrow I will cut off the tops and put it all in a paper sack for storage. I have about four of the largest heads picked out to use as seed for the fall. I also collected a whole bunch of chive seeds. I want to toss random flower seeds into the front flower beds and just see what grows. I am now going out to the apricot tree about every three days and picking up the ripe fruit off the ground. I keep about 75% of it and the rest I toss over the fence to the sheep. Our old ancient apple tree is shedding apples so I spent about thirty minutes cleaning them off the ground and tossing them over to the sheep. They love it. I was only able to pick about four apricots off the tree that were actually ripe. I like to wait until the fruit is full of sugar before picking it. When it is your tree you can wait until the very last minute. Annmarie and I cut and pitted about 12 cups for the freezer. We freeze them in one cup batches so she can use them for her breakfast smoothie. It takes a lot of frozen fruit to make it 365 days! We are going to be able to fill an entire upright freezer full of frozen fruit this year.
Well the coyotes are back, we have lost two lambs over the course of the last three weeks. For a while we could not spot them but now they are frequently visible and unfortunately very far away. Four of us have shot at them, some of us repeatedly and so far all we are doing is scaring them to run off. I realize that harassment is a valid tool for getting them to leave the sheep alone it is just not very final. If you don’t keep up the pressure than the predators just come back and start eating more animals.
I have been working on getting the tall fields with cheat grass in them mowed down so there are fewer places to hide for the coyotes. I am making pretty good progress but fields #3 & 4, still need a lot of mowing done. I carried a rifle for two straight days while I was mowing and only spotted one coyote. I missed repeatedly. I could use some practice but at the rate I am shooting at the coyotes I will be getting things dialed in soon.
We have not lost a lamb in the last two weeks. I go on patrol around the entire outside of the farm then drive two sides of the CRP looking for coyotes every couple of days. There is a path on the edge of the CRP now that I mowed in a couple of weeks ago. We need to get the weeds under control in the CRP and the edges are where the weeds are creeping in. I mowed a couple of weeks ago and will spray it this week. We are going for a good kill on the star thistle. The stuff is very nasty.
Once I have the edges of the CRP sprayed then I will work on the hillside and the backside of the field #1. I mowed there on Friday and knocked it back down. This also gives us great visibility for when the coyotes are moving through the fields. Normally coyotes will crawl under a fence but Annmarie spotted one this morning that just leaped over the fence! That is cheating! She was making our bed and spotted it just ambling by on the back hillside.
The Gingerman heard her and leaped out of bed and ran outside with a rifle. It was gone. I am pretty sure that it was the one I shot at up in field #2. I got dressed and went out looking in the pickup right after that to no avail.
As in all wise things one should probably look both ways before opening your mouth. I had finished putting together the baler, unfortunately, I missed a lower sprocket that drives the entire front end of the baler. It took an hour to extend the chain and fish it through the correct route. The route I had actually marked with arrows on the machine. Now we were ready to do until I tried to open the dump back and the hydraulic line blew a hole in it! It was the weekend so I had to wait until Tuesday to get the part built in Pendleton, it was Memorial Day weekend. I ordered the correct part first thing Tuesday morning from the Midwest and found a place in Pendleton that actually had metric fittings. Unfortunately, the new hose is bigger and it has a more robust end that means it’s more rigid. We had to put it on three times to find a way to feed it to the correct spot where it did not get pinched when the dump was raised and were it actually fit through the gaps. I had purchased a wrap to go around the outside. We had to remove that over a portion of the hose to get it to fit. We also had to stabilize it with some zip ties as it would not feed through the small opening the original tubing did. It works and it works like a champ! It sounds so much better and I only had to dig it out twice while making 300 bales (6 ton).
We have loaded 112 bales into the barn already, 100 bales went to Sarah and Gingerman for their horses. We have about another 150 bales that need to be picked up and put into the barn. We were pretty picky this year. The cheat grass is bad this year. So we only cut the good stuff. The Rejuvra is working, field one had some bare spots where no cheat grass grew this year. The orchard grass will slowly keep filling in. We are going to spray field 2, all around the machine shed and down by the school house with Rejuvra in the fall.
I think we are going to have to actually plow under the cheat grass. We could burn it but the risk is so high of it taking off that we will just turn it under, disc it then smooth it out.
I finished baling field two yesterday. I wanted to get started on cutting field 1 but I had no sooner gotten into the field when I hit a hidden piece of metal. This caused the blade to bind up as two teeth had popped off and lodged in place crooked to seize the blade in place. I had to go back to the shop, pull out the tooth bar and loosen up all of the clamps. I had the new teeth but the wrong size rivet. I was hoping that D & B carried the correct rivet as I knew that they had some over in fastener section. I found the rivets, they were longer than necessary but I was going to grind them down anyways so it didn’t matter. They had five different sizes of teeth for the mower and none of them will work, they are all too short. Luckily, I only needed the rivets.
I have never had to install teeth onto the bar before. I know you just pound out the rivet, set the new one, put it on a firm surface and bang on it with a big hammer, once flat then just grind it smooth on both sides. Sounds easy. We had an extra bar that got replaced last year so I went ahead and repaired them both. I had to use a 2.5” crescent wrench as a lever attached to a 22mm end wrench on bar guide nuts. They were incredibly stuck and would not come loose. I of course do not have a socket in metric bigger than 20mm. I managed to get the bar in place without cutting my fingers or gloves and it sounded great.
I managed to get once around the field before a different blade popped off and bound up the blade. I drove back, took it apart and was back in the field in under 45 minutes! Not bad, when you figure it takes me almost 8 minutes to drive out to the field. I managed to continue cutting all of field one until 2300. Half of the field is thin and the other half is very thick.
The mower has a guide on the end that is supposed to push the cut hay back into the middle but it was not working and my weld job lasted about ten minutes the first time. I struggled with it the entire time I was cutting field one. So this morning, Gingerman helped me out, I took it off, he welded the bolt in place from the other side and I straightened the piece out with a vice and 3# hammer. Then cut a support and bent it to fit. He welded the crack in the guide then welded the patch in place. He also welded the bolt hole smaller. I drilled the hole back out and put it all together again. It looks like it did originally and it appears that it will work accordingly. We just use any color of spray paint after any welding or repair job, it just so happens that there are a few cans of black out in the shop.
Mr Rainman should be able to get all of field one baled this week. A couple of the fields look good enough that we may be able to get a second cutting on them if we can get a little rain soon. Preferably after Thursday of this week.
Saturday was amazing, the sun was shining and it was a near perfect day. Since it was going to rain on Sunday we opted to just make it a work outside only day. Once the sheep were done we started to look for my set of small discs. Mr Rainman and I went all over the farm. We could not find them anywhere. I ended up mowing all around the upper CRP field. I mowed down by four corners but hit a buried baling twine bundle and had to take thirty minutes to cut it out of the mower blades.
The kids brought down a bunch of concrete from their remodel. We are going to use it to help stabilize the bank. It keeps getting eroded by the seeps, water and sheep. They have at least three more loads and I think that will make a great addition to this corner. We should be able to stop the corner from falling in.
The seven yearling cows that will be sold or eaten this fall got pushed down by four corners. They are in amongst the trees. We are going to start killing the cheat grass in the two fields near the mother-in-law’s house. We hope to get water on them so we can keep getting the cheat grass to sprout then kill it and start the process over.
I was able to sell five, one year old lambs this weekend ($120 each) so there are seven left to sell by this fall. It was very easy as we just pulled them off as we wormed the entire herd. They came and picked them up a couple of hours later. We just ran them out into the corral and down the chute into their horse trailer. The corral makes loading animals very easy.
The gate gremlins were out in force this weekend. The teenager cows got out of the lower pasture the gate was open. The horse got out of the barn lot, the gate was open. The horse got into the ran pasture with the sheep and was trying to eat the green grass, the gate was open. The surprising part of this is that each gate was left open by a different person! No one was harmed and the animals did just fine. This stuff happens.
I was able to get down to field one and mow the newly made ditch. Mr Rainman spotted some fresh coyote prints in the mud. We have not seen any yet this season but they are obviously out there. I went to the other side of the creek and worked on getting it mowed down. I managed to get the huge hole filled in! That has been there for over 25 years. Someone buried two huge track backhoes in there and spent three days trying to get them out. They left a huge hole that was never filled in. The edges of the hole were straight walled and over eight feet high. It is not safe to drive the tractor in that area without knowing exactly where you going and where the hole is located. I got the entire thing filled in and now anyone can safely go back there and mow it down as needed. That has been on my list for over 15 years and I just never got around to doing it. Usually, when I wanted to do it the ground was so hard that I could not move the dirt. I even used the little John Deere 2520 to do it.
Sunday I was able to work on the baler. Unfortunately, I am missing two parts. One that never got sent to me and one I think I sent back accidentally when I sent back the wrong sprockets. I am pretty sure that one is on me. I have the part numbers written down and will get them ordered first thing on Monday. Otherwise, all of the other parts are all installed, tightened and adjusted. I can get those two parts and the new chain on in less than 90 minutes. Mr Rainman did remind me that we may need to do some maintenance on the sickle bar mowers before we use them. I think I have all the parts for those already.
