Farmer Approved

It has been a very productive two days! I had Mr Rainman come out for Friday and of course it rained for a few hours. We cleaned up the machine shed, I worked on welding the weight holder for the three point auger. The soil is only moist for about the first two inches and then its very dry and our dirt has quite a bit of clay. The auger would not go down into the dirt. I had this idea to add 150# by welding on a tractor weight holder so we could put some weight on the auger. Since I had tried the auger for 30 minutes and was getting nowhere we opted to go back to the shop and do some welding. I just keep digging around in the old burn pile and the pile of scrap that keeps coming out of the ground. I have a pile started outside the machine shed and I just dig through it looking for something that will work. If you cover it all up with paint after you are done it covers up a lot of mistakes. I have learned to hit it hard with a hammer afterwards to just make sure it holds. We still had to dig out a small center part of the hole in three of the six holes as we could not get the auger to dig down without it, but it went fairly smooth after that. We were able to do 2 of 6 holes without doing anything. The first day we set the railroad ties in gravel and then used the Mistress (John Deere) to drive in the T-posts. I did have to fill the bucket with gravel and then throw on an extra 150# of tractor weights into the bucket to get enough weight to push in the T-posts. I still had to use the bucket as a driver on three T-posts. It is not elegant but with the bolt on T-post driver I have it does the job. We called it a day after that as I did not have any splicing tubes so I needed to go to town. Annmarie and I went shopping then had dinner afterwards. It was nice.

Saturday we did not have to fight the rain, just the cold! It was 40 degrees and the sun would not come out of the clouds. I felt like an a decrepit old soul trying to get out of bed this morning. I had a hard time sleeping as my entire back and upper arms felt like they were on fire all night long. I started out slow by doing more welding and Mr Rainman, cleaned out the machine shed some more and made the mower ramp for my mother-in-law for her new shed. He also moved the old John Deere baler over to the tractor tool area and away from the machine shed, therefore opening up another bay in the machine shed. I welded some gate latches out of scraps laying around or dug out of the ground. I had to clean the parts up a little bit with the grinder first as I could not get a good spark through all of the corrosion. Some of my later pieces look better than the early ones. Maybe if I keep this up I may be able to do some not so ugly welding.

The wind was blowing and with the cold spell the trees have finally started to drop leaves. My solution to leaves is the same as mowing the grass, I put the sheep in the front yard! I did it first thing this morning and will do it all day tomorrow also. The dogs go on the run so they cannot harass the sheep and the sheep know to stay away from the dogs. They also know the dogs cannot get at them, how they know that I do not know.

I had to run back to town to get the right size splices, the one I picked up the day before was too small. We got all of the wire up, attached and the gates hung in about four hours. The new battery powered fence stapler is the bomb!! It just slams through driving staples. We had all the wooden stays up in under ten minutes, push, hold the trigger, machine whines then slams a staple into the stay. I love using the high tension wire and tighteners now to make H-braces. It keeps them taut and if they get loose at all they are incredibly easy to tighten. Which is not true when you use wooden stays and smooth wire twisted together.

I even managed to sell our old ram as ground mutton this week! He will be going to a good home that will appreciate what he has to offer. I think I still have one cow left to sell.

One thought on “Farmer Approved

  1. Dave Keeler October 31, 2021 / 10:49 am

    I see an open u-joint on the post hole digger. You ever see what a spinning u-joint will do when it catches some cloth of your shirt? RIP YOUR ARM RIGHT OFF AT THE SHOULDER !!! Fix it.

    Liked by 1 person

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s