naked gardener

Granary progress

Steve HardinLeave a comment

Well the granary situation has improved dramatically. It was going to cost almost $700 in sheet metal and welding wire to make another 5x5x5’ bin and one of the nephews sent me a link for a local person selling two large upright bins! I did not need both of them despite their willingness to sell me both. So for $750 they delivered it to the house on Friday. I had cleared a spot and dropped a bunch of gravel in place but after looking at the container I think I need to level the area and then drill five holes in the ground, add some wire and fill them up with concrete. I can take a piece of all thread and put it into the concrete when it’s wet. I don’t think I will try and line up the holes with the grain bin. I will just weld some plates and bolt them in place.

I also managed to get some paint sprayed on the finished bin I repaired and got the slider door installed. Of course when I used a chain to roll the bin I bent the brand new door. I crawled inside and beat it back into shape with a hammer. It works now, it’s a little stiff but that is not a bad thing as I want opening the door to be an intentional act. It looks like the bin has a ladder built into its side so someone can climb the bin and open the top when filling it. This is a good thing as long as you are not scared of heights. I will have to get the cap removal process down before we lift it into the air. I would like to stand on the ground while learning, not holding onto the ladder with one arm 25’ into the air while fighting the lid with the other.

The Naked Gardener called on Thursday to say that he thinks his field is ready to cut again. I swung by on Friday and he is right, it is ready. So I spent most of the day Friday tearing the baler apart. I figured out that it is a lot easier to work on if you remove the front arms and some extra pieces. It took about an hour to disassemble the front but it was a lot easier getting to everything else. There was one guide piece I could not remove but I just worked around it. I was going to have to grind the nuts off and it is just not necessary as I am not replacing it. I replaced about 1/3 of the pickups and tubes. Anything that was bent got tossed in the trash. I have about an hour left to get the races lined up and then I can spend another hour putting the front all back together. I also need to replace a hydraulic hose. The entire thing is covered in hydraulic fluid. It needs a wash down.

Unfortunately, I am on a timer now. I went over and cut the field this evening. So the new tractor “Juicy” has had a flat tire for two weeks in the upper field, I had to go up and remove the tire tonight so it can be fixed. The hay turner is on the back and it needs about 45 minutes of TLC before I can go turn the hay. Once that is done then I will need to spend three hours with the baler to get it up and running so I can bale the hay!

I also will need to install the two new gates on our stairs to prevent the grandchild from crawling up and falling down from the bottom or falling down the stairs from the top. This is what happens when your grandparents work in the hospital and see bad stuff all the time.

The new chickens area settling in nicely. All of them are staying out of the yard which is good for them as being a play toy for the dog tends to an eventual slow death.

We now have three kittens living under the old house porch. We have installed a temporary fence to keep Mouse away from them as he is a definite kitten killer. He only comes on weekends with the kids. Of course, the kittens don’t know this so they were going through the fence as they are now starting to become very active. So we now have a plastic chicken netting zip tied to the fence so the kittens cannot get through the fence. Milo likes the kittens so we will work on socializing him to them. He still does not like their mother and barks at her whenever he sees her.

Haying again

Steve HardinLeave a comment

I had more haying to do over the weekend. I cut down what looked good at the neighbor’s. The weather was so warm that I had to turn it in 24 hours and was baling it the next day. I did have to finish putting the baler together before I could bale anything. I have decided that I will need to chain up the baler next time I work on it. I need to take both of the support arms off of it so I can get into the internal pickups much easier. I am wasting time trying to squeeze myself into a little area and work in a cramped space. If I chain the front part up so it does not fall then I can just chock the wheels and work on it with nothing in the front. I only need to remove two bolts to get it off.

I took some time on Friday to go over and pickup an old horse arena, some homemade panels and scrap pipe from the Naked Gardener. I think I will use them to circle the hay pile I am putting up next to the grain bins. The four homemade panels are for the spring crossing. I have panels from another horse arena set installed there now and this will allow me to pull all those panels back together to form a circle.

I baled Saturday until it got so hot that the grass would no longer bale. I came back out after dinner and worked until 2330. The grass was baling very well but I was tired after a 16 hour day and was ready for bed. I busted a shear bolt because I was not paying attention to what I was doing, I think I dozed off so the quitting time whistle was blown and I went home, cleaned up and went to bed so I could be out by 0730 and baling again. I needed to bale in the morning before it got too hot. I was able to bale for two hours before I heard a clang and the shear bolt snapped again. I tried to replace the shear bolt but I could not turn the pickups by hand. So I had to move some grass around and I discovered the broken pickup string of three pickups that had broken loose and jammed the works up. I was talking with Mr Rainman and after the baler rebuild last year with all new chain sprockets and new chains we think all of the slop is gone and now the weak point is the old bolts in the pickup area. I had already placed an order for more parts and now I need to wait until they come then order the rest of the parts to change out all of the internal pickup forks and all of the bolts. I have 2-3 bent pickup guides and those will need to be changed out also. A total rebuild of the internal pieces so that all the weak spots go away.

We got some hanging baskets and I installed two hooks on the front porch. We are going to see how the baskets do in the wind before we install more hooks. We would like to have hooks all across the entire front porch with flowers hanging down. It would look very cool!